Item Tag: Sander Drive Shaft

2×72″ Belt Grinder wheels-5″ Drive-24 mm shaft, 3″ Track-2″ Idler-Hinge Bracket Note: Set Does Not include any mounting Axles/Bolts Wheel Set Description Set Includes:One 130 mm (5.1″) diameter Drive Wheel: Drive wheel is CNC machined with 24 mm bore (H7 tolerance). Bore is equipped with a 8 mm key way and a set screw. Wheel is 55 mm wide (2.2″). Bore is 35 mm long (1.4″). Surface of wheel is truly crowned to insure belt won’t jump off wheel . Please refer to the wheel’s sketch for the exact wheel dimensions Two 50 mm diameter Idler Wheels: Each wheel is CNC machined and fitted with three 12 mm bearings. (Heavy duty 6201 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load) One 75 mm diameter Track Wheel: Each wheel is CNC machined and fitted with three 12 mm bearings. (Heavy duty 6201 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load)One Hinge Bracket for the Tracking Wheel: Made from Steel ShippingWe understand that customers would like to receive their purchase as soon as possible. Therefore I provide postage service that is comparable -in speed- to local postal service. And to achieve that:All orders are shipped using GLS or FedEx economy depending on destination All order are shipped the same working day if paid by 3 PM central European time From experience, in most cases; Items arrive in 2-6 work days to all EU countries From experience, in most cases; Items arrive in 4-10 work days to North America From experience, in most cases; Items arrive in 5-15 work days to Australia and New Zealand Limitation of Liability In no event shall pulley-wheel be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of its products.

Belt Grinder wheel set knife grinder 5.1″ Drive 19 mm shaft 3″ tracking, 2″ IdlerCNC machined from Aluminum 6061 Note: Set Does Not include any mounting Axles/Bolts Wheel Set Description Set Includes:One 130 mm (5.1″) diameter Drive Wheel: Drive wheel is CNC machined with 19 mm bore (H7 tolerace). Bore is equipped with a 6 mm key way and a set screw. Wheel is 55 mm wide (2.2″). Bore is 35 mm long (1.4″). Surface of wheel is truly crowned to insure belt won’t jump off wheel . Please refer to the wheel’s sketch for the exact wheel dimensions Two 50 mm diameter Idler Wheels: Each wheel is CNC machined and fitted with three 12 mm bearings. (Heavy duty 6201 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load) One 75 mm diameter Track Wheel: Each wheel is CNC machined and fitted with three 12 mm bearings. (Heavy duty 6201 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load)One Hinge Bracket for the Tracking Wheel: Made from Steel ShippingWe understand that customers would like to receive their purchase as soon as possible. Therefore I provide postage service that is comparable -in speed- to local postal service. And to achieve that:All orders are shipped using GLS or FedEx economy depending on destination All order are shipped the same working day if paid by 3 PM central European time From experience, in most cases; Items arrive in 2-6 work days to all EU countries From experience, in most cases; Items arrive in 4-10 work days to North America From experience, in most cases; Items arrive in 5-15 work days to Australia and New Zealand Limitation of Liability In no event shall pulley-wheel be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of its products.

Belt Grinder Wheel Set CNC machined from Aluminium 6061This is as good as it can getRunout less than 0.05 mm Guaranteed (Extreme CNC Machining) Wheel Set Description We are proud to introduce our Newest Belt Grinder wheel set.Set Includes: One 198 mm (7.8 inch) Diameter Drive Wheel – 55 mm wide: Drive wheel is CNC machined with 5/8″ bore (H7 tolerance). Bore is equipped with a 3/16″ key way and a set screw. Surface of wheel is truly crowned to insure belt won’t jump off wheel . Please refer to the wheel’s sketch for the exact wheel dimensions – Bore length is 40 mm (1.6″) Two x 65 mm (2.5″) diameter Idler Wheels – 55 mm wide: Each wheel is fitted with Four 12.70 mm (1/2″) bearings. (Heavy duty 6201-1/2″ RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 11 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load)One 130 mm diameter Track Wheel – 55 mm wide: Large Tracking wheels adds considerable control and stability of the sanding belt (from experience)Each wheel is fitted with Four 12.7 mm (1/2″) bearings. (Heavy duty 6201-1/2″ RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). 11 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load) ShippingWe understand that customers would like to receive their purchase as soon as possible. Therefore I provide postage service that is comparable -in speed- to local postal service. And to achieve that:All orders are shipped FedEx EconomyAll order are shipped the same working day if paid by 3 PM central European time From experience, in most cases; Items arrive in 3-6 work days to all EU countries From experience, in most cases; Items arrive in 3-8 work days to North America and AustraliaLimitation of Liability In no event shall pulley-wheel be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of its products.

Belt Grinder wheel set knife grinder 5.1″ Drive 5/8″ shaft 3″ tracking, 2″ Idler Wheel Set Description Set Includes:One 129 mm (5.1″) diameter Drive Wheel: Drive wheel is CNC machined with 5/8″ mm bore (H7 tolerance). Bore is equipped with a 3/16″ key way and a set screw. Wheel is 55 mm wide (2.2″). Bore is 38 mm long (1.5″). Surface of wheel is truly crowned to insure belt won’t jump off wheel . Please refer to the wheel’s sketch for the exact wheel dimensions Two 50 mm diameter Idler Wheels: Each wheel is CNC machined and fitted with three 1/2″ bearings. (Heavy duty 6201-1/2 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). A 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load) One 75 mm diameter Track Wheel: Each wheel is CNC machined and fitted with three 1/2″ bearings. (Heavy duty 6201-1/2 RS bearings) Bearings are rubber sealed to protect from dust. Bearings are placed back to back (best combination). A 10 mm wide standoff (sleeve) will raise the wheel of the mounting plate. This bearing combination is the best tested solution against bearing failure as it allow for tightening the mounting bolts without causing any axial force on the bearings (ball bearings should not bear lateral load) ShippingWe understand that customers would like to receive their purchase as soon as possible. Therefore I provide postage service that is comparable -in speed- to local postal service. And to achieve that:All orders are shipped using GLS and FedEx economyAll order are shipped the same working day if paid by 3 PM central European time From experience, in most cases; Items arrive in 3-6 work days to all EU countries From experience, in most cases; Items arrive in 7-15 work days to North America From experience, in most cases; Items arrive in 7-15 work days to Australia and New Zealand Limitation of Liability In no event shall pulley-wheel be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of its products.